THE MEUSER MOLD
EASY
+ stands tilted by itself
+ no clamp needed
+ lid always sits right
+ List with quantities
EFFICIENT
+ Easy to open
+ Rounded ends
+ big sprues
+ big inlets
Made in Germany
+ Robust design for a long life
+ Designed by goldsmiths
The three models
Bachelor
- 2 sprues for wire
- Wire up to 22 g silver or 30 g gold (750/-), sufficient for 2.5 m wire with a diameter of 1 mm
Master
- 2 sprues for wire
- 1 sprue for sheet metal (thickness 3 mm)
- Wire up to 22 g silver or 30 g gold (750/-), sufficient for 2.5 m wire with a diameter of 1 mm
- Sheet metal up to 32 g silver or 47 g gold (750/-)
Doctor
- 3 sprues for wire
- 2 sprues for sheet metal (thickness 4 mm)
- Wire up to 40 g silver or 58 g gold (750/-), sufficient for 4.7 m wire with a diameter of 1 mm
- Sheet metal up to 80 g silver or 120 g gold (750/-)
Casting ingenuity that works
EASY
- Specially constructed lid closes tight using solely its own weight, no clamp is needed to hold it.
- The legs double as a guide for the lid, so it sits exactly right every time. No need to adjust it manually.
- The mould is built to stand by itself at an angle. This design allows the liquid metal to gently flow into the mould rather than just falling in. This results in a better quality finish as the chance of trapping air bubbles is minimal.
- The amount needed to fill the inlets is engraved in the mould. You never have to calculate the weights again!
EFFICIENT
- Two inlets for plaits allow casts up to 120g of gold (18kt) or 85g of silver.
- The sprues are very big, making it safe and comfortable to cast in the liquid metal.
- The ends of the casted pieces are round, making it easier to roll them and avoiding loss of material.
- There are three inlets for wire with equally large diameters but different lengths. A bigger diameter is much easier to cast compared to a thin one. This leads to best results every time.
- Opening the mold is easy and fast. This way the cast can be quenched in water straight away, to give it a finer grained structure and a better quality.
- The mold can be heated before use to keep the casted metal liquid for a longer time.
Made in Germany
- All parts are made in Germany
- Developed by the industry for the industry... The mold was developed by a goldsmith who knows the problems from experience, and has created a fast easy and workable solution.
The MEUSER MOLD is availlable from the following distributors:
Germany
Rudolf Flume
Technik GmbH
45127 Essen
Karl FISCHER GmbH
75172 Pforzheim
DT & Goldart
97708 Bad Bocklet
R. Götze GmbH & Co. KG
10785 Berlin
Horbach Industriebedarf GmbH
55743 Idar-Oberstein
Gebr. Ott GmbH
63450 Hanau
Carl Engelkemper
48155 Münster
Benelux
Bijou Moderne
NL – Bleiswijk
Coertel
Antwerp, Belgium
Denmark
Aktiv Guld AS
Copenhagen
Sweden
Aktiv Guld AB
Malmö
If you are a distributor ...
… and whish to receive an offer or should you have any question regarding the MEUSER MOLD, feel free to contact me at +49 151 5191 2022 (mobile) or at Phil.Meuser@mailbox.org
Developed by a goldsmith for goldsmiths
Dipl. Ing. Philipp Meuser graduated as goldsmith at the Staatliche Zeichenakademie Hanau in 2005 and studied mechanical engineering at the University of Applied Sciences Schweinfurt with a focus on product development